ZCuZn31Al2 flange bronze bushing

ZCuZn31Al2 flange bronze bushing

ZCuZn31Al2 Flange Bronze Bushing

The ZCuZn31Al2 flange bronze bushing is a cast aluminum brass bearing with an integral collar that locates a shaft and supports light axial loads. Built from the ZCuZn31Al2 alloy, also known as CuZn31Al2, it pairs moderate strength with good resistance to corrosion in air, fresh water, and seawater, plus straightforward machinability. These traits make it a practical option for pressure castings, marine fittings, and general machinery components.

What Is ZCuZn31Al2 Aluminum Brass

ZCuZn31Al2 is a cast copper alloy covered by the Chinese standard GB/T 1176. The leading Z marks it as a casting, while the name shows about 31 percent zinc and 2 to 3 percent aluminum. Outside China the same material is referenced as CuZn31Al2, and it is sometimes called 31-2 aluminum brass. It is a high zinc brass strengthened by aluminum, not a leaded tin bronze, so its properties and price sit in a different category from bearing bronzes such as C93200. For composition data on other copper alloys, visit our materials page.

The ZCuZn31Al2 flange bronze bushing sits between low cost cast brass and the higher strength bearing bronzes in both price and performance.

Chemical Composition of ZCuZn31Al2

The composition limits below follow GB/T 1176. Figures are mass percent.

Element Content (mass %) Note
Copper (Cu) 66.0 to 68.0 base element
Zinc (Zn) remainder (balance)
Aluminum (Al) 2.0 to 3.0 main strengthener
Lead (Pb) <= 1.0 not counted in impurity total
Tin (Sn) <= 1.0 not counted in impurity total
Iron (Fe) <= 0.8 impurity
Manganese (Mn) <= 0.5 impurity
Total impurities <= 1.5

Mechanical Properties of ZCuZn31Al2

Mechanical minimums depend on the casting method. Metal mold (chill) casting cools faster than sand casting, giving finer grains and higher strength and hardness. The minimum values below are taken from GB/T 1176-2013.

Property Sand cast (min) Metal mold cast (min)
Tensile strength >= 295 MPa >= 390 MPa
Elongation (A) >= 12 % >= 15 %
Brinell hardness (HBW) 80 to 130 typical 90 to 130 typical

A caution on hardness: a few online tables print a Brinell value near 885 HB for this alloy. That number is not consistent with a cast brass and is almost certainly a transcription error copied between suppliers. Use the 80 to 130 HB range above for design, and confirm the exact figure on the mill certificate for your batch.

The GB/T 1176 standard does not set a minimum yield strength for this alloy. Typical yield for sand cast parts is around 120 MPa, but the value depends on section thickness and should be confirmed on the mill certificate.

Casting, Machining, and Welding

ZCuZn31Al2 flows well in the mold and suits both sand and metal mold casting. Pouring temperatures are typically around 1000 to 1050 C. The alloy machines at a moderate rate and can be joined by common methods such as brazing or gas tungsten arc welding; a stress relief anneal after welding is advisable. These qualities support flange bushings produced to a customer drawing, whether as cast blanks or finish machined parts.

Machining and Dimensional Tolerances

Flange bushings are usually supplied as cast blanks and then finish machined to the drawing. Allow a machining envelope on the bore, outside diameter, and flange faces, because the as cast surface is not a finished fit. For press or slip fits into a housing, specify the required ISO tolerance grade, commonly H7 for the bore and a light interference for the outside diameter, and confirm it against the casting method, since metal mold parts hold tighter dimensions than sand cast parts.

Typical Applications of ZCuZn31Al2 Flange Bushings

The mix of corrosion resistance, castability, and moderate cost suits the ZCuZn31Al2 flange bronze bushing to several duty types:

  • Pressure and die castings: motor housings, instrument bodies, and other parts where a cast brass bushing is seated into a larger casting.
  • Marine and shipbuilding: rudder stocks, stern tube bearings, and seawater exposed fittings where resistance to corrosion matters more than high hardness.
  • General machinery: guide bushes, spacers, and thrust washers in equipment that runs at moderate load and speed. For sliding wear surfaces, review our wear plate options.
  • Valve and pump parts: bodies and seats that must resist fresh and salt water.

For many of these duties the ZCuZn31Al2 flange bronze bushing replaces a stamped or turned steel spacer. Note the limits: as a bronze bushing material, ZCuZn31Al2 is meant for moderate sliding speeds and loads. It is not a substitute for hardened steel or bimetal bearings in high pressure, high speed joints. Supply lubrication where possible, and keep surface pressure and velocity within the range validated for cast brass. For a broader comparison of plain bearing materials, see our bronze bushing overview.

ZCuZn31Al2 Flange Bronze Bushing Design Notes

The flange acts as a built in locating shoulder and a face for light axial thrust. When specifying, confirm the bore tolerance, outside diameter, flange thickness, and overall length against the mating housing. Because properties vary with wall thickness and cooling rate, a separately cast test bar can read higher than the finished bushing. For press fit assembly, allow for the difference between the as cast outside diameter and the machined finish. Most ZCuZn31Al2 flange bushings are made to order rather than bought from shelf stock.

Solid vs Self Lubricating Versions

A standard ZCuZn31Al2 flange bronze bushing depends on an external lubricant film. Where lubrication is intermittent or unavailable, a graphite embedded bronze bushing, with solid graphite plugs or pockets in a high strength copper alloy, can run with little or no oil. That is a separate product family described on our graphite bronze bushing page. Choose the solid cast version when cost and corrosion resistance lead the decision, and the graphite type when maintenance access is limited.

Corrosion Behavior in Service

In seawater the aluminum content helps form a protective surface film, but the high zinc level means dezincification can occur in stagnant or acidic conditions. For continuously submerged, high stress marine shafts, confirm the alloy choice with the application engineer; a nickel aluminum bronze such as C63000 is often preferred for the most demanding seawater duties. In normal air and fresh water service, ZCuZn31Al2 performs reliably with basic maintenance.

How ZCuZn31Al2 Compares to Other Bushing Alloys

ZCuZn31Al2 is one option among several copper alloys used for plain bearings. A leaded tin bronze such as C93200 includes lead present as a separate soft phase that improves sliding lubrication, but it resists seawater corrosion less well and costs more per kilogram of alloy. Aluminum bronzes such as C95400 and C95500 are stronger and harder and suit heavier loaded shafts, at a higher price. ZCuZn31Al2 targets the middle: good corrosion resistance, moderate strength, and low material cost. Review our materials page for a full alloy list and our bronze bushing overview for how these families fit different duties.

Specifying and Ordering

When requesting a ZCuZn31Al2 flange bronze bushing quote, send the drawing with tolerances, quantity, and the required casting method, because metal mold and sand cast parts differ in strength. State the service environment, fresh water, seawater, or dry indoor, so the supplier can confirm suitability. Our bronze bushing overview compares alloy families, and the materials page lists composition data for other copper alloys.

Summary

The ZCuZn31Al2 flange bronze bushing is a cast aluminum brass part for marine, pressure casting, and general machinery uses where corrosion resistance and moderate cost are the priority. Its composition and mechanical properties follow GB/T 1176, with strength set by the casting method. For design, verify hardness and tensile figures against the mill certificate, and select a self lubricating variant only when the duty cycle requires it. Contact BearingFace to discuss drawings and order quantities.

Design Custom Bearings Made From High-Strength Bronze Bearing

Custom Machine Parts & Custom Bronze Components –

Custom Bronze Parts & Custom Bronze Bushing Bearing